OpenViBE forum

The OpenViBE community
It is currently Sat Dec 16, 2017 8:24 pm

All times are UTC




Post new topic Reply to topic  [ 7 posts ] 
Author Message
PostPosted: Wed Nov 05, 2014 7:09 pm 
Offline

Joined: Fri Oct 31, 2014 9:06 pm
Posts: 2
I have the Olimex OpenEEG and have got it all connected and running.
I've loading the tie fighter demo and replacing the file reader component with the live signal input.
( Also tried with a recorded file )

However the tie fighter game just sits at READY?

I'm not 100% sure where to put the electodes... have 4 active and one passive.... I have been placing 2 electrodes around the Cz area, and labeling the channel Cz....

What other steps are required to get the demo running correctly.

Thanks,
Kevin Macey


Top
 Profile  
Reply with quote  
PostPosted: Wed Nov 12, 2014 2:00 pm 
Offline

Joined: Sun Mar 14, 2010 12:58 pm
Posts: 108
Hi Kevin,

You could get the updated Tie-Fighter scenarios that we presented at the recent OpenViBE workshop, there:

1:30-2:15pm: Fabien Lotte, Alison Cellard, Inria Bordeaux Sud-Ouest, France, “Hands-on tutorial with actual EEG recordings: Motor Imagery-based BCI design“
pdf of the slides: http://openvibe.inria.fr/openvibe/wp-co ... tation.pdf
Demo : OpenViBE-workshop_spaceship-demo - openvibe scenarios: http://openvibe.inria.fr/openvibe/wp-co ... r-demo.zip

Hopefully it can answer your questions!

Let me know,

Best regards,
Fabien


Top
 Profile  
Reply with quote  
PostPosted: Fri Nov 14, 2014 1:21 pm 
Offline

Joined: Fri Oct 31, 2014 9:06 pm
Posts: 2
Thanks for the quick reply, will check out the slides and demo... Will post my results here afterwards...


Top
 Profile  
Reply with quote  
PostPosted: Fri Jul 01, 2016 11:12 am 
Offline

Joined: Wed May 11, 2016 8:41 am
Posts: 7
Hi Fabien, would it be possible to get the source code for the tie fighter/spaceship demo, so I can edit it on ogre3d to fit my project?


Top
 Profile  
Reply with quote  
PostPosted: Fri Jul 01, 2016 9:38 pm 
Offline

Joined: Thu Jun 30, 2016 4:17 pm
Posts: 3
I have set up the tie fighter example based off the scenarios in the zip file and the slides provided. I am using an OpenBCI V3-32 board and online signals as my input. I am using FCz,C1,Cz,C2,and CPz However, the tie fighter game just sits at READY?

Any ideas on how to fix this?

Thanks,
Morgan


Top
 Profile  
Reply with quote  
PostPosted: Fri Dec 01, 2017 1:36 pm 
Offline

Joined: Sun Oct 29, 2017 9:54 am
Posts: 5
Hi, in the paper « https://hal.archives-ouvertes.fr/hal-01366873 », an OpenVIBE scenario to calibrate the « Use-The-Force » game is mentioned.
How could I get this scenario ?
Regards,
Gilles


Top
 Profile  
Reply with quote  
PostPosted: Tue Dec 05, 2017 9:42 pm 
Offline

Joined: Sun Oct 29, 2017 9:54 am
Posts: 5
gqueneherve wrote:
Hi, in the paper « https://hal.archives-ouvertes.fr/hal-01366873 », an OpenVIBE scenario to calibrate the « Use-The-Force » game is mentioned.
How could I get this scenario ?
Regards,
Gilles

Forget this post : I've just seen that everything needed about Tie-Fighter demo is in the .zip archive just above in Fabien Lotte's post.


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group
Americanized by Maël Soucaze.